Carbonetic Single pro carbon clutch Mazda RX7 FD3S. Complete inc lightened flywheel.
Choice of 2 clamping force plates 1300kg or 1600kg
Flywheel Weight 4.5KG
Complete 9.1 KG
Approx 500 bhp rating
There is a massive 5.25 kg weight saving between an Exedy single clutch and this Carbonetics clutch.
Please allow 800 miles for bedding in.
find out more

Carbonetic Blade for Mazda RX7 FD3S

£332.74

Carbonetic BLADE has been developed to provide an uprated clutch, with a stock feel at an OEM price. Clutches dont get any better than this. Specifically designed to fit in to your already fitted stock cover of your Mazda RX7 FD3S.
Approx 400 bhp rating. Blade disc 1.45KG
find out more

Carbonetic S-Spec front pad for RX7 FD

£122.96

Carbonetic S-Spec front pad for RX7 FD3S
CARBONETIC SUPER STREET pad is designed to improve overall braking performance of any street vehicles. SUPER STREET pad is developed for street and light track use where initial stopping power and resistance to fade is of prime importance. In addition to reducing brake dust and squeal, these long-lasting pads help keep rotor wear to minimum.

Applicable Rotor Temp
0-500 degrees C
Friction Coefficient
0.32-0.42
find out more

Magnecor 8mm leads for mazda RX7 FD 8bit UK

£46.99

Magnecor 8mm leads for mazda RX7 FD 8bit UK
Original equipment replacement.Designed to improve original ignition system performance on road vehicles using either electronic engine management systems or carburetors.Ideal for LPG gas conversion engines.Excellent RFI and EMI suppression.Flexible high-strength all silicone construction.
These are almost identical in length to the 16bit but have a straight cap where it connects to the coils.
Lead lengths approx, centre of cap to centre of cap each end.
T1 = 22cm, T2 = 28cm
L1 = 28cm, L2 = 33cm
find out more

RotaryArt full block kit

£178.06

RotaryArt full block kit: comprising of coolant seals, 4 inner and 4 outer square, dowell O rings 4 total , front cover O ring 1 total, oil filter base O rings 2 total, 20 total thrubolt O rings, rear stationary gear O ring 1 total and the oil control O rings 4 inner green and 4 outer black.

find out more

East Caost Parts 13b 2mm ALS Apex seals

£362.02

East Caost Parts 13b 2mm ALS Apex seals. Designed to be unbreakable so no engine damage if it lets go under pressure and designed to compliment there lightweight billet rotors.
find out more

5ltr Dexelia Ultra 5w30

£41.03

Dexelia oils are the only oil recognised by Mazda for the use in there RX8. Any other oil could void the manufacturers warentee.
find out more

1ltr Dexelia Ultra 5w30

£9.20

Dexelia oils are the only oil recognised by Mazda for the use in there RX8. Any other oil could void the manufacturers warentee.
find out more

Mazda RX8 ignition coil

£64.63

Genuine Mazda RX8 ignition coil. These are a known problem for their short life span, and some customers now treat these as a consumable, checking them at every service. Priced each, all four should be checked.
We are now able to offer these at almost half the Mazda recommended retail price and on average you will save approx £170 on a set.
find out more

Visit our new forum www.rotarycommunity.com

Bonnet accessories

Online Catalogue | Aero & Styling kits | Exterior styling | Bonnet accessories

Tein Bonnet damper RX7

Price: £80.00 (£94.00 Including VAT at 17.5%)

Tein Bonnet damper RX7 FD

Tein Bonnet damper RX8

Price: £90.00 (£105.75 Including VAT at 17.5%)

Tein Bonnet damper RX8
Bonnet raised at hinge side by approx 3mm from OEM position

Top fit non locking catch

Price: £29.95 (£35.19 Including VAT at 17.5%)

These are fixed from the top with screws so are not truely flush fitting, but are quick and easy to install.

Top fit locking catch

Price: £33.55 (£39.42 Including VAT at 17.5%)

These are fixed from the top with screws so are not truely flush fitting, but are quick and easy to install.

Flush non locking catch

Price: £29.95 (£35.19 Including VAT at 17.5%)

These are fixed from below by bonding to the bonnet so are truely flush fitting. More care needs to be taken in the cut out and installation.

Flush locking catch

Price: £33.55 (£39.42 Including VAT at 17.5%)

These are fixed from below by bonding to the bonnet so are truely flush fitting. More care needs to be taken in the cut out and installation.

Locking flush fitting bonnet locks

Price: £14.50 (£17.04 Including VAT at 17.5%)

Locking bonnet pins, flush fitting finished in hard wearing chrome

flush fitting bonnet locks quick release

Price: £6.32 (£7.43 Including VAT at 17.5%)

Non locking quick release bonnet pins, flush fitting finished in hard wearing chrome

Stainless Steel Competition bonnet pins

Price: £10.00 (£11.75 Including VAT at 17.5%)

Stainless steel bonnet pins, competition pins, quick release.

Ali Competition bonnet pins

Price: £11.75 (£13.81 Including VAT at 17.5%)

colours

Ali bonnet pins, competition pins, quick release.

Recessed bonnet pin cups

Price: £7.00 (£8.23 Including VAT at 17.5%)

For a truely professional look use the cups with your existing bonnet pins and create a areodynamic fitting bonnet pin, for use with Ali and Stainless competition pins above.
Available in black & silver

Spoiler & splitter steady bars

Price: £9.24 (£10.86 Including VAT at 17.5%)

Spoiler & splitter steady bars, supplied in pairs and can be used for reducing vibration and movement in froont splitters and spoilers.

Adjustable spoiler & splitter steady bars

Price: £11.90 (£13.98 Including VAT at 17.5%)

2 way adjustable spoiler & splitter steady bars, supplied in pairs and can be used for reducing vibration and movement in froont splitters and spoilers.

Online Catalogue | Aero & Styling kits | Exterior styling | Bonnet accessories

Visit our new forum www.rotarycommunity.com